Factory Source Pe Supplier - Polyethylene PE1000 Rod – UHMWPE – Beyond
Factory Source Pe Supplier - Polyethylene PE1000 Rod – UHMWPE – Beyond Detail:
Uhmw Pe 1000 Rod :
PE Rod is odourless, non-toxic, feel like wax, has good low temperature resistance (the lowest temperature can reach 70 ~ 100 °C), chemical stability is good, most of acid and alkali erosion (acid) with characteristics of oxidation resistance, temperature does not dissolve in solvents, small water imbibition, excellent electrical insulation properties;Low density;Good toughness, also apply to low temperature conditions);Good stretchability;The electric and dielectric insulation;Bibulous rate is low;The water vapor permeability is low;Good chemical stability;Non-toxic harmless.
But PE Rod for environmental stress (chemical and mechanical effect) is very sensitive, heat aging.
Medical appliance parts, seals, cutting boards, sliding profiles. Widely used in chemical industry, machinery, chemical industry, electric power, clothing, packaging, food and other industries.Widely used in gas transmission, water supply, drainage, irrigation, mines fine particles of solid conveying, and oil field, chemical industry and telecommunications and other fields, especially on the gas supply has been widely used.
Advantges of the uhmwpe rod:
1. Good Tensile strength
2. High impact and anti impact strength
3. High heat deflection temperature
4. High strength and hardness
5. Good glide and soft home characters
6. Good chemical stability against organic solvents and fuels
7. Resistant to thermal aging (applicable temperature between -60°C and 190°C
8. Size alternation by humidity absorption must be considered
Application fields of the uhmwpe ROD:
Wearparts , transmission parts , home appliance parts , automotive parts , wire rod to prevent the machine parts , chemical machinery parts, chemical equipment , such as turbine , gear ,bearing , impeller , shaft , dashboard, drive shaft ,valve , blades , wire rod , high pressure washers , screws ,nuts , seals, shuttle bushing , connector , etc
Rods size
| Colour | Rod Length (mm) | Rod Diameter (mm) | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | - | 20 | 25 | 30 | 35 | 40 | 50 | 60 | 65 | 70 | 80 | 90 | 100 |
| Natural | 2000 | * | * | * | * | * | * | * | * | * | * | * | * |
| Natural | 1000 | * | * | * | * | * | * | * | * | * | * | * | * |
| Black | 2000 | * | - | * | - | * | * | * | * | * | * | * | * |
| Black | 1000 | * | - | * | - | * | * | * | * | * | * | * | * |
| Green | 2000 | * | - | - | - | * | * | * | - | * | * | * | * |
| Green | 1000 | * | - | - | - | * | * | * | - | * | * | * | * |
| Blue | 2000 | * | - | - | - | * | * | - | - | - | * | - | * |
| Blue | 1000 | * | - | - | - | * | * | - | - | - | * | - | * |
| Colour | Rod Length (mm) | Rod Diameter (mm) | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | - | 110 | 120 | 130 | 140 | 150 | 160 | 180 | 200 | 230 | 250 | 300 |
| Natural | 2000 | * | * | * | * | * | * | * | * | * | - | - |
| Natural | 1000 | * | * | * | * | * | * | * | * | * | * | * |
| Black | 2000 | * | * | * | * | * | * | * | * | - | - | - |
| Black | 1000 | * | * | * | * | * | * | * | * | * | * | * |
| Green | 2000 | * | * | * | * | * | * | * | * | - | - | - |
| Green | 1000 | * | * | * | * | * | * | * | * | - | - | - |
| Blue | 2000 | - | * | - | - | - | - | - | - | - | - | - |
| Blue | 1000 | - | * | - | - | * | - | - | - | - | - | - |
Specification of UHMW-PE compared to other Engineering Plastic
| Item | Unint | UHMW-PE | ABS | PA-66 | POM | PTFE |
| Density | g/cm^3 | 0.935 | 1.03 | 1.41 | 1.41 | 2.14-2.30 |
| Flash Point | ºC | 136 | 165 | 25 | 165 | 327 |
| Friction Factor | – | 0.1-0.22 | – | 0.15-0.40 | 0.15-0.35 | 0.04-0.25 |
| Water Absorption Rate | % | <0.01 | 0.20-0.45 | 1.5 | 0.25 | <0.02 |
| Tensile Strength | MPa | ≥38 | 22-28 | ≥80 | 62-70 | 15-35 |
| Elongation at Break | % | ≥300 | ≥53 | ≥60 | ≥40 | 200-400 |
| Impact Strength | KJ/m^2 | 70 | ≥22 | 4.5 | – | – |
| Volume Resistivity | Ω.cm | 10^17 | 10^15 | 5*10^14 | 10^14 | >10^17 |
| Breakdown Potential | KV/mm | 50 | 15 | 15 | 20 | 20 |
| Dielectric Constant | 10^6HZ | 2.2 | 2.4 | 3.7 | 3.7-3.8 | 1.8-2.2 |
| Dielectric Loss Tangent | 10^6HZ | ≤5*10^-4 | 4*10^-2 | 2*10^-2 | 5*10^-2 | ≤2.5*10^-4 |
Our Advantages:
A: Experienced uhmwpe products supplier
B: Professional design team and sales department for your service
C: We can provide free small sample or receive small quanty sample order.
D: 8/24 service for you, all the questions will be dealed within 24 hour
E: Stable quality—-coming from good material and technic
F: Lower price—-not cheapest but the lowest at the same quality
G: Good service—-satisfactory service before and after sale
H: Delivery time—-15-20 days for mass production
Product detail pictures:
Related Product Guide:
We have many excellent staff members good at marketing, QC, and dealing with kinds of troublesome problem in the production process for Factory Source Pe Supplier - Polyethylene PE1000 Rod – UHMWPE – Beyond , The product will supply to all over the world, such as: Czech Republic, Thailand, Atlanta, We'd like to invite customers from abroad to discuss business with us. We can present our clients with high quality products and excellent service. We're sure that we'll have good cooperative relationships and make a brilliant future for both parties.
By Juliet from Greek - 2017.10.23 10:29
In China, we have many partners, this company is the most satisfying to us, reliable quality and good credit, it is worth appreciation.
By Ivan from India - 2018.12.28 15:18
