Factory Free sample Polyethylene Pe Sheet – Polyethylene PE1000 Rod – UHMWPE – Beyond
Factory Free sample Polyethylene Pe Sheet – Polyethylene PE1000 Rod – UHMWPE – Beyond Detail:
Uhmw Pe 1000 Rod :
PE Rod is odourless, non-toxic, feel like wax, has good low temperature resistance (the lowest temperature can reach 70 ~ 100 °C), chemical stability is good, most of acid and alkali erosion (acid) with characteristics of oxidation resistance, temperature does not dissolve in solvents, small water imbibition, excellent electrical insulation properties;Low density;Good toughness, also apply to low temperature conditions);Good stretchability;The electric and dielectric insulation;Bibulous rate is low;The water vapor permeability is low;Good chemical stability;Non-toxic harmless.
But PE Rod for environmental stress (chemical and mechanical effect) is very sensitive, heat aging.
Medical appliance parts, seals, cutting boards, sliding profiles. Widely used in chemical industry, machinery, chemical industry, electric power, clothing, packaging, food and other industries.Widely used in gas transmission, water supply, drainage, irrigation, mines fine particles of solid conveying, and oil field, chemical industry and telecommunications and other fields, especially on the gas supply has been widely used.
Advantges of the uhmwpe rod:
1. Good Tensile strength
2. High impact and anti impact strength
3. High heat deflection temperature
4. High strength and hardness
5. Good glide and soft home characters
6. Good chemical stability against organic solvents and fuels
7. Resistant to thermal aging (applicable temperature between -60°C and 190°C
8. Size alternation by humidity absorption must be considered
Application fields of the uhmwpe ROD:
Wearparts , transmission parts , home appliance parts , automotive parts , wire rod to prevent the machine parts , chemical machinery parts, chemical equipment , such as turbine , gear ,bearing , impeller , shaft , dashboard, drive shaft ,valve , blades , wire rod , high pressure washers , screws ,nuts , seals, shuttle bushing , connector , etc
Rods size
| Colour | Rod Length (mm) | Rod Diameter (mm) | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | - | 20 | 25 | 30 | 35 | 40 | 50 | 60 | 65 | 70 | 80 | 90 | 100 |
| Natural | 2000 | * | * | * | * | * | * | * | * | * | * | * | * |
| Natural | 1000 | * | * | * | * | * | * | * | * | * | * | * | * |
| Black | 2000 | * | - | * | - | * | * | * | * | * | * | * | * |
| Black | 1000 | * | - | * | - | * | * | * | * | * | * | * | * |
| Green | 2000 | * | - | - | - | * | * | * | - | * | * | * | * |
| Green | 1000 | * | - | - | - | * | * | * | - | * | * | * | * |
| Blue | 2000 | * | - | - | - | * | * | - | - | - | * | - | * |
| Blue | 1000 | * | - | - | - | * | * | - | - | - | * | - | * |
| Colour | Rod Length (mm) | Rod Diameter (mm) | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | - | 110 | 120 | 130 | 140 | 150 | 160 | 180 | 200 | 230 | 250 | 300 |
| Natural | 2000 | * | * | * | * | * | * | * | * | * | - | - |
| Natural | 1000 | * | * | * | * | * | * | * | * | * | * | * |
| Black | 2000 | * | * | * | * | * | * | * | * | - | - | - |
| Black | 1000 | * | * | * | * | * | * | * | * | * | * | * |
| Green | 2000 | * | * | * | * | * | * | * | * | - | - | - |
| Green | 1000 | * | * | * | * | * | * | * | * | - | - | - |
| Blue | 2000 | - | * | - | - | - | - | - | - | - | - | - |
| Blue | 1000 | - | * | - | - | * | - | - | - | - | - | - |
Specification of UHMW-PE compared to other Engineering Plastic
| Item | Unint | UHMW-PE | ABS | PA-66 | POM | PTFE |
| Density | g/cm^3 | 0.935 | 1.03 | 1.41 | 1.41 | 2.14-2.30 |
| Flash Point | ºC | 136 | 165 | 25 | 165 | 327 |
| Friction Factor | – | 0.1-0.22 | – | 0.15-0.40 | 0.15-0.35 | 0.04-0.25 |
| Water Absorption Rate | % | <0.01 | 0.20-0.45 | 1.5 | 0.25 | <0.02 |
| Tensile Strength | MPa | ≥38 | 22-28 | ≥80 | 62-70 | 15-35 |
| Elongation at Break | % | ≥300 | ≥53 | ≥60 | ≥40 | 200-400 |
| Impact Strength | KJ/m^2 | 70 | ≥22 | 4.5 | – | – |
| Volume Resistivity | Ω.cm | 10^17 | 10^15 | 5*10^14 | 10^14 | >10^17 |
| Breakdown Potential | KV/mm | 50 | 15 | 15 | 20 | 20 |
| Dielectric Constant | 10^6HZ | 2.2 | 2.4 | 3.7 | 3.7-3.8 | 1.8-2.2 |
| Dielectric Loss Tangent | 10^6HZ | ≤5*10^-4 | 4*10^-2 | 2*10^-2 | 5*10^-2 | ≤2.5*10^-4 |
Our Advantages:
A: Experienced uhmwpe products supplier
B: Professional design team and sales department for your service
C: We can provide free small sample or receive small quanty sample order.
D: 8/24 service for you, all the questions will be dealed within 24 hour
E: Stable quality—-coming from good material and technic
F: Lower price—-not cheapest but the lowest at the same quality
G: Good service—-satisfactory service before and after sale
H: Delivery time—-15-20 days for mass production
Product detail pictures:
Related Product Guide:
We are going to dedicate ourselves to providing our esteemed buyers together with the most enthusiastically thoughtful products and services for Factory Free sample Polyethylene Pe Sheet – Polyethylene PE1000 Rod – UHMWPE – Beyond , The product will supply to all over the world, such as: New Orleans, Georgia, New Delhi, Our products are widely recognized and trusted by users and can meet continuously changing of economic and social needs. We welcome new and old customers from all walks of life to contact us for future business relationships and mutual success!
By olivier musset from Lesotho - 2018.11.06 10:04
The factory technical staff not only have high level of technology, their English level is also very good, this is a great help to technology communication.
By Megan from Oman - 2018.02.12 14:52
-
New Delivery For High Molecular Weight Plastic ...
-
Discount wholesale Uhmw Sheets Near Me - PA6 N...
-
Wholesale Pe Ground Protection Mat - Polyethyl...
-
Big Discount Uhmwpe Silos Liner - Outrigger pa...
-
Factory Source Mc Nylon Material - Soccer Rebo...
-
Hot-Selling Pom Rod - High quality food grade ...
